Unilock Construction in Highland, CA

Unilock Construction in Highland, CA | Moreno Valley Builders

We’re Moreno Valley Builders, an independent general contractor providing Unilock paver and wall construction across Highland and Unilock in Redlands. We plan, source, and install Unilock systems here with the foothill conditions in mind: expansive clay, Santa Ana winds, and WUI fire requirements that most paver contractors never address. For Unilock driveways, patios, and retaining walls in Highland, call (877) 752-3154 for a free estimate.

Call (877) 752-3154

Why Highland Residents Choose Us for Unilock Service

We specify Unilock because their paver bodies hold up to the Inland Empire’s temperature swings better than most pressed concrete products. But the real difference is how we install them. Noel Trevino, our owner and general contractor, grew up in Sunnymead Ranch and has spent three decades ripping out failed hardscape across the region. He knows what goes wrong under Highland’s specific soil conditions because he’s dug into enough failed jobs to see the pattern. We’re not manufacturer-affiliated or authorized. We’re independent, which means we fix what’s actually wrong on your property, not what a corporate install manual assumes.

Our crews handle the full project scope: excavation, base preparation, paver layout, edge restraint, and the coordination with any adjacent work like drainage or landscaping. One contractor. Every phase. If a project involves a retaining wall next to a driveway or a patio that ties into the home’s foundation, we manage those transitions so the details don’t fall through the cracks between trades.

Common Unilock Construction Problems We Solve in Highland

• Efflorescence blooming on Brussels Block pavers. Winter rains pull salts through the paver body, and when the base doesn’t drain, those salts crystallize on the surface as chalky white streaks. On Highland’s heavier clay soils, poor base drainage makes this worse. We can clean the surface, but the permanent fix starts with an open-graded base and proper slope.
• Beacon Hill Flagstone edge spalling. This is surface flaking at paver edges, often caused by point loads when bedding sand is uneven. Hot-weather pours in Highland demand early-morning work and curing attention. We see spalling on jobs where the bedding layer wasn’t fully compacted before the pavers went down.
• Copthorne sett joint sand washout. Santa Ana winds drive rain sideways through these wider-joint setts, stripping the joint sand in a single storm season. Once the sand washes out, units go loose and rutting follows. We use polymeric sand rated for wind-driven rain and we re-sand as part of standard maintenance on exposed Highland lots.
• Pisa2 retaining wall lean and face cracking. The classic hillside problem. When the original install skips geogrid on a sloped lot, seasonal clay movement pushes the wall face forward until blocks crack. Off Boulder Avenue and the surrounding foothills, this is the most expensive repair we do because it’s structural, not cosmetic.
• Edge restraint failure on driveways. Here, plastic edging moves and the outer pavers separate. It’s usually a base-depth problem. Highland’s clay shrinks in summer and swells in winter, so we over-excavate and build bases on more generous lifts than you’d need in sandy soil flatland cities.

Unilock Service in Highland: What Local Conditions Mean for Your Equipment

Highland sits inside a wildland-urban interface zone, which means the city enforces WUI building codes that flatland communities don’t. That changes hardscape work in ways most homeowners don’t expect. If your Unilock retaining wall sits near a structure, it may need a noncombustible wall cap detail. If pavers run up against the house, the plan may need to coordinate with your defensible-space layout. We’ve done Pisa2 wall rebuilds off Boulder Avenue where the original contractor never pulled a permit because the wall was under height. It wasn’t. The city flagged it during a fire-safety inspection, and the fix cost triple what the original job did. When we build in Highland, we check the WUI requirements first, then design the hardscape around them. It’s slower up front, but it keeps the project legal and the structure defensible come fire season.

Unilock Models & Products We Service in Highland

We work with the Unilock product lines most common in Highland’s older neighborhoods and newer foothill builds. Brussels Block is the workhorse for driveways and walkways. Beacon Hill Flagstone brings a more natural flagstone look to patio applications. Copthorne is the choice for larger-format sett patterns. Pisa2 handles retaining walls from garden heights up to structural applications. For paver repairs, we source genuine Unilock units so color and dimension match the existing field. For base and joint materials, we use aftermarket polymeric sands and aggregates where they outperform the OEM spec, especially on Highland’s clay. We keep common replacement units and sands staged through our supplier network for shorter turnaround on Highland jobs, because most of our leads for Unilock sales & service in this area are repair-driven, not new-build.

Unilock Service Pricing in Highland

FAQs – Unilock Construction in Highland

Service Areas Near Highland

Moreno Valley Builders covers Highland and the surrounding foothill and valley communities. We work in Highland service area zip code 92346, plus Moreno Valley, Grand Terrace, Loma Linda, and Highgrove. If you’re farther east toward the pass, we also provide Unilock service in Rialto and Unilock service in Romoland.

Book Your Unilock Service in Highland Today

Call (877) 752-3154 to schedule your free estimate. We’ll send a qualified hardscape lead to your Highland property, assess the soil and existing base, and give you a written scope with real numbers. If the details aren’t right on paper, they won’t be right in the wall.

Written by Noel Trevino, Owner & General Contractor at Moreno Valley Builders, serving Highland and the Inland Empire.